Here’s a new Knowledge Base article we published. This one talks about an issue where Ntbackup on Windows Server 2003 fails with "Error: The device reported an error to the request to write data to media".
Consider the following scenario:
· System Center Virtual Machine Manager 2008 R2 (SCVMM) is used to perform a physical to virtual conversion (P2V) of a Windows Server 2003 system. · After the conversion completes, performing a backup using Ntbackup in the Windows Server 2003 virtual machine may fail with the following error:
Error: The device reported an error to the request to write data to media. The NTbackup log file contains the following information:
Error: The device reported an error to the request to write data to media. Error reported: Invalid command. It must be a hardware problem or media. Check the relevant errors in the system event log. Operation has been completed. Error: <Drive Letter>: is not a valid drive or have access to that drive.
After doing a P2V, the VM may have a partition size greater than the disk size as seen in MSinfo32 of the VM.
To work around this issue, manually increase the size of the VHD to be larger than the partition size as displayed in the VM's MSinfo32 information. To increase/expand the size of the VHD we can do the following:
Method 1: Using SCVMM 2008 R2
1: In the SCVMM console go to the Properties of the VM and then to the Hardware Configuration tab. 2: In the left Pane select the vhd file and in the main pane, check the box Expand the virtual hard disk. 3: Put in the disk size, just enough to be bigger than the size of the partition that was seen in Msinfo32. 4: Click OK and wait till the job completes the change of the virtual machine properties.
Method 2: Using Hyper-V Manager In Hyper-V
1: In the Hyper-V console go to the settings of the VM, and select the ‘Hard Drive’ in the left pane. 2: In the Main pane under Media, click on Edit, this will open the ‘Edit Virtual Disk Wizard’. 3: Select Expand and click Next. 4: Put in the disk size, just enough to be bigger than the size of the partition that was seen in Msinfo32. Then click Finish.
Please note: Both the above methods work for both Dynamic and Fixed VHDs. Both the above methods have to be performed with the VM turned off.
For the most current version of this article please see the following:
2728970 - Ntbackup on Windows Server 2003 may fail with the following error after the system is converted using P2V: "Error: The device reported an error to the request to write data to media"
J.C. Hornbeck | System Center & Security Knowledge Engineer
Get the latest System Center news on Facebook and Twitter:
App-V Team blog: http://blogs.technet.com/appv/ ConfigMgr Support Team blog: http://blogs.technet.com/configurationmgr/ DPM Team blog: http://blogs.technet.com/dpm/ MED-V Team blog: http://blogs.technet.com/medv/ Orchestrator Support Team blog: http://blogs.technet.com/b/orchestrator/ Operations Manager Team blog: http://blogs.technet.com/momteam/ SCVMM Team blog: http://blogs.technet.com/scvmm Server App-V Team blog: http://blogs.technet.com/b/serverappv Service Manager Team blog: http://blogs.technet.com/b/servicemanager System Center Essentials Team blog: http://blogs.technet.com/b/systemcenteressentials WSUS Support Team blog: http://blogs.technet.com/sus/
The Forefront Server Protection blog: http://blogs.technet.com/b/fss/ The Forefront Endpoint Security blog : http://blogs.technet.com/b/clientsecurity/ The Forefront Identity Manager blog : http://blogs.msdn.com/b/ms-identity-support/ The Forefront TMG blog: http://blogs.technet.com/b/isablog/ The Forefront UAG blog: http://blogs.technet.com/b/edgeaccessblog/
ntbackup.exe is a Windows Backup. For details <a href="internetworksolutions.net/.../">cisco ccie</a>